|Feb 4, 2013, 11:22 AM||#1|
SSD TRIM Support in RAID 0 or Concatenation
Hi, I have a 2012 Mac Mini Server with 2 x 256 GB SSDs and wanted to run them either in RAID 0 or Concatenation to get one large 512 GB drive. Is the TRIM command enabled in any of these configurations? If not, is there a way I can combine the drives into one volume and get TRIM enabled?
|Feb 4, 2013, 09:22 PM||#7|
Software RAID in it's current iteration cannot pass hardware information about it's component parts to reporting utilities.
If you 'get info' (disk utility, system info) about the hardware pieces, they will correctly report attributes like SMART and TRIM.
Last edited by MatthewAMEL; Feb 4, 2013 at 09:31 PM.
|Feb 5, 2013, 03:21 PM||#8|
FYI, I purchased both SSDs from apple (pre-installed, BTO system). I went ahead and did the RAID 0 setup as instructed in the Apple support pages. My system info now says: "TRIM Support: Yes" for both drives while they are in RAID 0. I don't know whether TRIM is truly enabled or just "supported."
My research did yield that Intel enabled TRIM for SSDs in RAID 0 for their recent desktop 7 series chipsets. The mac mini has HM77 (Mobile version of the 7 series chipset). Since the RAID via Disk Utility is software based, I don't think this is relevant. Would have been nice if apple used the built-in hardware RAID.
I am aware of the data loss potential. I have a synology DS412+ NAS for data, synology DX213 (4TB) for local backup, and Amazon glacier for off-site back up.
|Feb 12, 2013, 06:45 PM||#9|
I should clarify...
Softraid is paid software, though you can do builds with the free trial.
Here is an excerpt from their site.
SoftRAID version 4.5 includes all of the incredible features first seen in the version 4.0 release that shipped a year ago. Most of these features are not found in any other RAID solution for Mac OS X. These include: Fast Mirror Rebuilds which allow a mirror (RAID 1) volume to be rebuilt in minutes rather than hours, full validation of all data on volumes and disks, certification of disks to ensure that all sectors can read and write data correctly, a complete email notification system to remotely notify you of any disk or volume error, use of SMART data to predict disk failure and a command line interface for all disk and volume functions. It is also the only RAID solution for Mac OS X which supports TRIM on SSDs.
|Feb 13, 2013, 07:17 PM||#10|
It's oft misunderstood...
Using software/hardware RAID results in a 'volume' that is composed of multiple 'physical' devices.
TRIM (and Garbage Collection) is a firmware/hardware function. It could care less about the volume structure it's a part of.
By default, Apple enables TRIM on any Apple-branded SSD. There are multiple ways to enable TRIM on non-Apple SSD's.
The performance of a particular SSD is dependent on the OS being TRIM aware, the firmware TRIM and the Garbage Collection routine. All 3 are necessary for optimal performance of a SSD.
|Thread Tools||Search this Thread|
|thread||Thread Starter||Forum||Replies||Last Post|
|JDOD vs RAID 0 (SSD without TRIM, Snow Leopard)||LeandrodaFL||Mac mini||2||Dec 7, 2013 12:51 PM|
|SSD TRIM support||Ashwee||MacBook Pro||2||May 22, 2013 04:59 AM|
|TRIM support for aftermarket SSD's?||ThomasJL||OS X 10.8 Mountain Lion||24||Apr 2, 2013 08:54 AM|
|TRIM support for Second SSD||Shirke||Mac mini||3||Mar 3, 2013 03:57 PM|
|Raid 0 With SSD and Trim||Prime85||MacBook Pro||3||Jul 1, 2012 03:19 PM|
All times are GMT -5. The time now is 12:26 PM.