|Dec 29, 2012, 01:28 AM||#1|
Problems with Link Aggregation and a Mini
Santa brought me a huge pile of useless crap, but also new network equipment: a Cisco 20-port managed switch (SRW2016-K9)
I'm currently trying to set up a new network environment. For better performance I want the designated server (a Mac Mini 2011 running 10.8.2) to use link aggregation on two ports (the native ethernet port and one via a Thunderbolt adapter).
Both connections receive their IP addresses through DCHP from another router when plugged in > connection established.
I then created a network bond in sysprefs/network ('manage virtual interfaces' > 'new link aggregate' with both ports. No problems so far.
On the switch I set port speed to 1000Mbit and full duplex mode for both ports (Port Management/Port Settings). Then I added both ports to one LAG enabling LACP.
However, only one member - the Thunderbolt Ethernet - was recognized and went green (OS X/sysprefs/advanced). The light for the native port is blinking, changing between red and orange. The error messages 'Invalid Link' ('The link state was not valid, i.e. down, half-duplex, or wrong speed') and 'No Partner' ('The port on the switch that the device is connected to doesn't seem to have 802.3add Link Aggregation enabled.') are changing accordingly.
The port on the switch in which the native ethernet is plugged into is 'down' (no LED).
I checked the physical connections, exchanged cables and used different ports - no avail. When I connect two Macs (one of which is the above mentioned Mini) with two patch cables directly, the connection works just fine.
I further tested link aggregation in a similar setup (Mini 2012 and Display Ethernet and a Retina MBP with two Thunderbolt Ethernet adapters). > no problems AT ALL!
Any hints are greatly appreciated!
|Jan 8, 2013, 03:18 PM||#4|
try not manually configuring the ports and letting them auto-negotiate
I would configure the LAG on the switch first, then add the connections in osx. this shouldn't make a difference but your setup should be working anyway so let's not let logic get in the way of things
you sure it wasn't in a spanning-tree wait state when you first plugged the ethernet in? try and put the port in portfast so it can negotiate immediately?
Last edited by freejazz-man; Jan 8, 2013 at 03:43 PM.
|Feb 1, 2013, 09:56 AM||#6|
I'm at work right now but my home network is set up similar to what you want to do; I'm using a Cisco 200-series (no CLI like your 300-series, but otherwise identical) and a Mac Pro. I have it working with an 802.3ad bundle between the two, along with .1q trunking over said bundle. What I can't remember is whether I enabled LACP on the bundle or not. I'll check when I get home and reply back here. Either way, first thing's first: get auto-neg running on both ends of both links.
|Feb 2, 2013, 12:19 AM||#7|
|Feb 5, 2014, 12:24 PM||#8|
| 2014 13" rMBP i5 | 2013 13" MBA i7 | 2012 Mac Mini i7 | 2012 13" MBP i5 | 2008 13" MB c2d | 2006 iMac c2d | iPad Air | iPad 3 | iPhone 6 | iPhone 5 | iPhone 4S | iPhone 4 | iPhone 3 |
|Feb 9, 2014, 01:44 PM||#9|
|Thread Tools||Search this Thread|
|thread||Thread Starter||Forum||Replies||Last Post|
|Link aggregation with Thunderbolt->Ethernet adapter?||radiogoober||Mac OS X Server, Xserve, and Networking||10||Sep 2, 2014 04:14 PM|
|Mac Mini Server Link aggregation - Thunderbolt or USB 3 gigabit ethernet adaptors||gavcooper||Mac OS X Server, Xserve, and Networking||21||Aug 19, 2014 02:55 PM|
|Ethernet Link Aggregation W/ Thunderbolt Display||ThisIsNotMe||Mac Peripherals||11||Feb 6, 2014 08:57 AM|
|iMac with Link Aggregation using Thunderbolt to Ethernet?||nemesis379||Mac Peripherals||3||Apr 18, 2013 11:22 AM|
|Link aggregation under Mountain Lion problem||sporadic||Mac Pro||15||Oct 21, 2012 10:55 AM|
All times are GMT -5. The time now is 07:05 PM.