How do I install BestSkinsEver?

Discussion in 'iPad Accessories' started by ronaldcastillo, Jun 22, 2011.

  1. macrumors 6502

    Joined:
    Oct 25, 2009
    #1
    I completely don't know how to install BestSkinsEver full protector on my iPad 2. Could anyone simply tell me how to install it on correctly? Will Best Buy install them for a certain fee? I haven't done this before.
     
  2. macrumors regular

    Firen

    Joined:
    Jun 15, 2009
    Location:
    Vienna, Austria
  3. macrumors member

    Joined:
    May 1, 2011
  4. macrumors 68000

    iphone1105

    Joined:
    Oct 8, 2009
    #4
    Just curious, but why buy something you have no knowledge of or how to use?
     
  5. macrumors 68030

    Joined:
    Apr 10, 2003
    Location:
    A hot desert
    #5
    You've never bought something new to you? I just bought an antenna to install on my roof, I've never done that before.

    Why answer with such an inane question?
     
  6. macrumors 6502

    Joined:
    Jan 26, 2010
    #6
    LOL owned! :D

    so did you get one installed? i am just planning on how to apply mine!
     
  7. macrumors regular

    Joined:
    May 15, 2011
    #7
    Hahahahaha you tell 'em! What a waste of an answer.
    Anyways I found the YouTube videos helpful. I was really nervous about all the water and potential for water damage. Don't DRENCH it but apply relatively liberally witha spray bottle, one or two sprays covering the whole heet is enough. As I was using my squeegee (credit card) on the back I would place the towel that was underneath at the edge just as my card got there so that excess water would get absorbed right away. This was especially important near the ports and speaker (iPad 2). I tried taping them with scotch tape which you can do but when the soap makes contact the adhesive comes
    Off anyways.Also don't worry about how it
    Looks right after you're finished. It really does change overnight and mine looks awesome. Just one bubble where I could have bene a bit more diligent. It's not visually noticeable, you can feel it though. I only applied one to the back, I like keepin my front screen naked. It's protected almost all the time anyways. I have the protector, maybe I'll give it a shot.
    Good luck.
     
  8. glen e, Jul 8, 2011
    Last edited: Jul 8, 2011

    macrumors 68030

    Joined:
    Jun 19, 2010
    Location:
    Ft Lauderdale
    #8
    No I think hooligan is right...if you can find this forum, post this question, then you can find expert directions from the mfr....I wish there was an intelligent "watcher" that when stuff like this was posted, would intercept it and send them to google.

    My point is someone can come on here and tell you the install is "a snap" but forget to tell you he installs decals/tint for a living...you never know where things come from in cyberspace," so see what the mfr says and then make a decision on what to do....
     
  9. macrumors 6502

    Joined:
    Jan 26, 2010
    #9
    Hmm...maybe people should have sent you to google yourself?!
    http://forums.macrumors.com/showthread.php?t=1147295&highlight=
    http://forums.macrumors.com/showthread.php?t=1115944&highlight=
    http://forums.macrumors.com/showthread.php?t=1001840&highlight=

    point is - what's the point of having forums like this if you're just gonna direct everyone to google or the manufacturer? :p

    anyway...enough of this.
    back on topic.... did you get any dust under the BSE? did you go to the bathroom to make sure there was no dust?
     

Share This Page