Become a MacRumors Supporter for $50/year with no ads, ability to filter front page stories, and private forums.
All components (even mice and keyboards) have drivers. And yes it is possible that Leopard just isn't compatible with it. The card I have is only compatible with Tiger as well.

Ah ok, that's what I thought. So I'll make sure to look for one that's Leopard compatible.

FCS is still installing. Still going good.
 
I just found this firmware update for the card on Sonnet's website. I'm going to run this before I buy a new one. If it's a Leopard issue (which it says it 'improves performance under 10.5'), then this might fix it.

Otherwise it's just a busted card.

I've highlighted my card for anyone who might have had the same issues.

-------------------
Tempo Serial ATA PCIe/PCI-X Family Firmware Updater (Mac)

Version: 2.1.3
Posted Nov. 20, 2008
Description: This software updates 4-port and 8-port Tempo SATA host controller cards' flash ROM (firmware) to version 2.1.3. This version improves performance under Mac OS X Version 10.5 and fixes a SMART ReadLog and WriteLog issue.

Supported System Software: Mac OS X Version 10.2 and later

Supported Hardware: Tempo-X SATA 4+4, Tempo-X eSATA 4+4, Tempo-X eSATA8, Tempo SATA E4i, Tempo SATA E4P, Tempo SATA X4i, and Tempo SATA X4P


Note: This software runs only under Mac OS X. Not Supported; Tempo SATA E2P.
----------------------

So I'll try that after FCS is installed.
 
Status update....


I've reinstalled the RAID card. It seemed to be fine.

I've updated the RAID card's firmware to the latest from Sonnet's website.

Still seems to be fine.

One thing...

It's giving me an error message now when the RAID is connected (it's a small 4 disk setup, by the way).

It says "This disc was not repairable by this system. It has been made available to you with limited functionality. Please backup all your data and reformat the disc as soon as possible."

So I'm copying the data off the RAID, and doing a reformat.

Has anyone encountered that error before?

As for the freezing issue, so far so good.
 
I'm just in the middle of reformatting the RAID using Disk Utility.

It's been sitting at "Partitioning" (with the status bar at about 10%) for about an hour.

It's a 4 disk raid that adds up to 1TB.

Does it usually take this long?

I just went into Disk Utility and am using the Erase tab, formatting with Mac OS X Journaled.
 
Hey everyone.

I've searched the forums, and have come up with a couple of similar threads, but none seemed to have the answer.

I just installed Leopard twice on my G5. The system is a 2.5GHz dual-processor (not dual-core) G5. I can check the RAM on Monday when I go back to work, but I think it's 2 or 3GB?

It ran Tiger just fine, but the networking with Windows computers is so much better and faster with Leopard that it made sense to upgrade (the G5 is on a network mostly populated by PCs).

So.. we installed Leopard on it. Most of the time it will freeze a few minutes after bootup, even with a fresh install, and no programs added, just what comes with Leopard.

The freeze is a strange one. The entire system just stops. Power is still fed to the mouse and keyboard, but neither function. It's just dead. So you have to force shut it off, and then turn it back on.

Many times it will not boot up. Instead, the chime sounds, but the screen stays black, and the fans eventually go up to maximum.

Again, upon reboot, it will freeze up a few minutes later.

Sometimes it takes a while for it to freeze, and strangely enough if you're running a program, it might take a while for it to happen. But it does eventually stop running.

It didn't do this under Tiger, so it has to be a software issue.

But consider this...

I reformatted the drive again, this time opting to zero-out all the data as well.

A fresh install of Leopard seems to be fine. Then I run the software update. It freezes up before it finishes downloading all the updates.

So... is it a Leopard issue? I can find that out by reinstalling Tiger, but won't have the chance to do that until Monday. But we would really love to have Leopard on it because of the improved networking.

Or has something gone wrong with the hardware? I can't do a HW test because the original install discs that came with the G5 have gone missing.

Before I installed Leopard for the second time, I looked at the error logs. Nothing seemed out of the ordinary, but maybe I just missed something.
Another thing... it was fine for a while under Leopard. Then this started happening.

I can't remember what might have caused it, but here are the additional programs we've installed on it: Adobe After Effects, Final Cut Studio 2, Flip4Mac WMV Studio, and Adobe Premiere Pro.

Anyone else who has had this issue, have you come to a solution?

PS.
Does installing Bonjour on Windows really help with networking?
Also, any reason why the G5 has issues with which LAN port it's connected to? There's 2 ports near the G5. One works fine. The other does not. But the MacBook Pros can work on both. Perhaps it's related to the freezing issue.

When you update the OS, please unplug your external drive.
Go to Apple's site download the update individually.
I have a Areca card and it freezed up my MAC and after I restarted my MAC, I was not able to access to my RAID.
Contact my vendor www.timelinedigitalinc.com and they do have update on their site.
 
Register on MacRumors! This sidebar will go away, and you'll see fewer ads.